The PAL+BT comes with a USB-C to USB-C charging cable. Simply connect this cable to a USB-C PD compatible charger that is capable of delivering minimum 2.5 Watts and a maximum of 20 Watts. For the fastest charging, use a 20 Watt charger capable of delivering 9V / 2.2A.

To find radio stations, simply turn the tuning knob clockwise for a higher frequency, counter-clockwise for a lower frequency.

To save a preset, turn the radio on and find your desired station. Once you’re on the signal, press and hold the Preset button located on the remote control until you see “Preset Added” on the display. You can save up to 5 presets with the remote control. You can also access the Preset Store menu by double-pressing the Tune knob and using the knob to scroll through available presets. Single-press again to store the presets. You can save up to 10 presets using the Preset Store menu.

Your preset station will be indicated by a “P1-10” icon when it is tuned.

Alternatively, single-press the Tuning knob to access the Preset Store menu. Use the knob to scroll through your saved presets and single-press to select.

Press and hold the Menu/Select button on your remote until you see System appear on the display. Turn the Source knob till you see Scan Settings appear on the display. Press the Source button once. Turn the knob to select if you want to scan all stations or only strong station signals. Press the source button to make your selection. Repeat this process to change it back.

Hvis PAL+ BT flyttes til et annet område, kan det hende at enkelte stasjoner ikke lenger er tilgjengelige. Det anbefales at du kjører en full skanning hver gang du flytter radioen, selv i forskjellige områder av hjemmet ditt. For å kjøre en full skanning, gå inn i DAB-modus og trykk på menyknappen på fjernkontrollen for å gå inn i hovedmenyen. Velg Full skanning. For å avbryte skanningen, trykk på tilbakeknappen på fjernkontrollen.

Press and hold the Menu/Select button on your remote until System appears on the display. Press the Source button once. “Backlight” will show on the display. Press the Source button once. You can now turn the Source knob to the left to lower the brightness or the right to raise the brightness.

Make sure your PAL+BT is turned on and in Bluetooth source. Next, press and hold the Tune knob to enter pairing mode. Open the Bluetooth settings on your smart device and look for the “Tivoli PAL+BT3|xxxxx”. Select this to pair. You’ll hear a chiming noise once the connection is complete. You’ll only need to follow this process once. After you’ve paired for the first time, you’ll see the PAL+BT listed in your Bluetooth devices every time it’s turned on in Bluetooth mode.

When pairing with Bluetooth, make sure the volume on your smart device (phone, tablet, laptop) is set no higher than 75%. This will prevent any static or feedback noise.

Start by turning your PAL+BT off, and then on again. Press the Source knob to enter BT mode. Press and hold the Tune/Scan/Preset knob to enter pairing mode. Next, turn the BT on your smart device off and then on again. Now look for the PAL+BT in your list of available devices.

Yes. Press and hold the Menu/Select button till you see “Scan Setting” on the display. Use the arrows to navigate to the “Settings” menu, press the Menu/Select button once to confirm. Use the arrows until you see Factory Reset on the display. Press the Menu/Select to confirm.

Yes! You can use the PAL+BT while it’s charging. Please note that the batteries may charge more slowly while the PAL BT is in use.

The PAL+BT is designed to be a standalone speaker. It is not intended to be used with other speakers.

The average battery life is 12 hours on a single charge. Please note this can change depending on your music source and volume.

The PAL+BT is water resistant, but not waterproof. Take it to the pool, but don’t throw it in.

The rechargeable battery does not need to be changed, only recharged.